Sea-Bird Electronics SBE 38 Manual de usuario descargar pdf (Pagina 90)

Manual revision 006 Section 4: Deploying and Operating SBE 19plus V2 SBE 19plus V2

3. In the Open dialog box, select the .xmlcon or .con file and click Open.

Verify that the sensors match those on your 19plus V2, auxiliary sensors are

assigned to the correct voltage channels, and calibration coefficients for all

sensors are up-to-date.

4. Click Save or Save As to save any changes to the .xmlcon or .con file.

Click Exit when done reviewing / modifying the configuration.

Strain gauge or Digiquartz with

temperature compensation.

Click a sensor

and click Modify

to change

calibration

coefficients for

that sensor.

New to create new

.xmlcon or .con file

for this CTD.

Open to select

different .xmlcon or

.con file.

Save or Save As

to save current

.xmlcon or .con file

settings.

Channel/Sensor table reflects this

choice (0, 1, 2, 3, 4, 5, or 6). Must

agree with 19plus V2 setup for

VoltN= (N= 0, 1, 2, 3, 4, and 5);

see reply from GetCD or DS.

Voltage channel 0 in .xmlcon or

.con file corresponds to first

external voltage in data stream,

voltage channel 1 to second, etc.

Shaded sensors

cannot be removed

or changed to

another type of

sensor. All others are

optional.

• NMEA - Select if NMEA

navigation device used, and if

NMEA depth data and NMEA time

data were also appended.

Seasave adds current latitude,

longitude, and universal time code

to data header; appends NMEA

data to every scan; and writes

NMEA data to .nav file every time

Ctrl F7 is pressed or Add to .nav

File is clicked.

Note: Whether NMEA device was

connected to a deck unit or

directly to computer during data

acquisition in Seasave has no

effect on data file used by SBE

Data Processing, and therefore

has no effect on data processing.

• Surface PAR - Select if using with

deck unit connected to Surface

PAR sensor. Seasave appends

Surface PAR data to every scan.

Adds 2 channels to

Channel/Sensor table. Do not

increase External voltage

channels to reflect this; External

voltage channels reflects only

external voltages going directly to

19plus V2 from auxiliary sensor.

See Application Note 47.

• Scan time added - Select if

Seasave appended time (seconds

since January 1, 1970 GMT) to

each data scan.

Number of samples to average (samples at 4 Hz) in

Profiling mode. Used to calculate elapsed time, if

time is output parameter. Must agree with 19plus

setup (NAvg=); see reply from GetCD or DS.

Click a (non-shaded) sensor and click Select to pick a

different sensor for that channel. Dialog box with list of

sensors appears. Select sensors after number of

voltage channels have been specified above.

Interval between scans in Moored

mode. Used to calculate elapsed

time, if time is an output parameter.

Must agree with 19plus V2 setup

(SampleInterval=); see reply from

GetCD or DS.

SBE 38 (secondary temperature), WET Labs sensor

(up to 3 channels), up to 2 GTDs (dissolved oxygen or

nitrogen), or Optode. Must agree with 19plus

V2 setup;

see reply from GetCD or DS. Channel/Sensor table

lists RS-232 sensors below voltage channels.

Must agree with 19plus V2 setup (MP for Profiling mode,

MM for Moored mode); see reply from GetCD or DS.

1 2 ... 85 86 87 88 89 90 91 92 93 94 95 ... 123 124

Comentarios a estos manuales

Sin comentarios

Sea-Bird Electronics SBE 38 Manual de usuario Pagina 90

Comentarios a estos manuales