Sea-Bird Electronics SBE 38 Manual de usuario descargar pdf (Pagina 46)

Manual revision 006 Section 4: Deploying and Operating SBE 19plus V2 SBE 19plus V2

Status Commands (continued)

Moored Mode (MM)

• Firmware version, serial number, date

and time [DateTime=]

• Voltages and currents (main and back-up

lithium battery voltages, currents –

operating, pump, external voltage sensors,

RS-232 sensor)

• Logging status (not logging, logging, waiting

to start at . . ., or unknown status)

• Sample interval [SampleInterval=] and

number of measurements to take and average

per sample [NCycles=]

• Number of samples and available sample

space in memory

• Moored mode [MM], pump turn-on

parameter [MooredPumpMode=], and

pump turn-on delay

[DelayBeforeSampling=]

• Transmit data real-time?

[MooredTxRealTime=]

• Battery type [BatteryType=] and battery

cut-off voltage

• Pressure type [PType=] and range

[PRange=]

• Sample RS-232 sensor - SBE 38 [SBE38=],

WET Labs [WetLabs=], Optode [Optode=],

Gas Tension Device [GTD=], or dual Gas

Tension Devices [DualGTD=]?

• Sample external voltages 0, 1, 2, 3, 4, and 5

[Volt0= through Volt5=]?

• Show entered commands on screen as you

type [Echo=]?

• Output format [OutputFormat=]

• Output salinity [OutputSal=] and sound

velocity [OutputSV=] with each sample?

(only appears if output format =

converted decimal or converted XML UVIC)

• Output sigma-t, voltage, and current with

each sample? [OutputUCSD=]

(only appears if output format =

converted decimal or converted XML UVIC;

and if set to Y)

Example: Moored mode (user input in bold, command used to modify parameter in parentheses)

SBE 19plus V 2.3 SERIAL NO. 4000 15 Mar 2011 14:02:13 [DateTime=]

vbatt = = 10.1, vlith = 8.9, ioper = 61.9 ma, ipump = 20.8 ma,

iext01 = 76.2 ma,

status = not logging

sample interval = 15 seconds, number of measurements per sample = 1 [SampleInterval=, NCycles=]

samples = 0, free = 1644953 [reset with InitLogging]

mode = moored, run pump for 0.5 sec, delay before sampling = 0.0 seconds

[MM, MOOREDPUMPMODE=, DELAYBEFORESAMPLING=]

transmit real-time = yes [MooredTxRealTime=]

battery type = alkaline, battery cutoff = 7.5 volts [BatteryType=]

pressure sensor = strain gauge, range = 2000.0 [PType=, PRange=]

SBE 38 = no, WETLABS = no, OPTODE = no, Gas Tension Device = no [SBE38=, Optode=, WetLabs=, GTD=, DualGTD=]

Ext Volt 0 = yes, Ext Volt 1 = no [Volt0= and Volt1=]

Ext Volt 2 = no, Ext Volt 3 = no [Volt2= and Volt3=]

Ext Volt 4 = no, Ext Volt 5 = no [Volt4= and Volt5=]

echo characters = yes [Echo=]

output format = converted decimal [OutputFormat=]

output salinity = no, output sound velocity = no [OutputSal=, OutputSV=]

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 123 124

Comentarios a estos manuales

Sin comentarios

Sea-Bird Electronics SBE 38 Manual de usuario Pagina 46

Comentarios a estos manuales