Sea-Bird Electronics SBE 38 Manual de usuario Pagina 113
- Pagina / 124
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Manual revision 006 Appendix III: Command Summary SBE 19plus V2
113
CATEGORY COMMAND
DESCRIPTION
Calibration
Coefficients
(F=floating
point number;
S=string with
no spaces)
Dates shown
are when
calibrations
were
performed.
Calibration
coefficients
are initially
factory-set and
should agree
with
Calibration
Certificates
shipped with
19plus V2.
View all
coefficients
with GetCC
or DCal.
TCalDate=S
S=Temperature calibration date.
TAO=F
F=Temperature A0.
TA1=F
F=Temperature A1.
TA2=F
F=Temperature A2.
TA3=F
F=Temperature A3.
TOffset=F
F=Temperature offset correction.
CCalDate=S
S=Conductivity calibration date.
CG=F
F=
Conductivity G.
CH=F
F=Conductivity H.
CI=F
F=Conductivity I.
CJ=F
F=Conductivity J.
CPCor=F
F=Conductivity pcor.
CTCor=F
F=Conductivity tcor.
CSlope=F
F=
Conductivity slope correction.
PCalDate=S
S=
Pressure calibration date.
PRange=F
F=Pressure sensor full scale range (psia).
POffset=F
F=Pressure offset correction.
PA0=F
F=Strain-gauge pressure A0.
PA1=F
F=Strain-gauge pressure A1.
PA2=F
F=Strain-gauge pressure A2.
PTempA0=F
F=
Strain-gauge pressure temperature A0.
PTempA1=F
F=Strain-gauge pressure temperature A1.
PTempA2=F
F=Strain-gauge pressure temperature A2.
PTCA0=F
F=Strain-gauge pressure temperature compensation ptca0.
PTCA1=F
F=Strain-gauge pressure temperature compensation ptca1.
PTCA2=F
F=Strain-gauge pressure temperature compensation ptca2.
PTCB0=F
F=Strain-gauge pressure temperature compensation ptcb0.
PTCB1=F
F=
Strain-gauge pressure temperature compensation ptcb1.
PTCB2=F
F=Strain-gauge pressure temperature compensation ptcb2.
PC1=F
F=Quartz pressure C1.
PC2=F
F=Quartz pressure C2.
PC3=F
F=Quartz pressure C3.
PD1=F
F=Quartz pressure D1.
PD2=F
F=
Quartz pressure D2.
PT1=F
F=Quartz pressure T1.
PT2=F
F=Quartz pressure T2.
PT3=F
F=Quartz pressure T3.
PT4=F
F=Quartz pressure T4.
PSlope=F
F=Quartz pressure slope correction.
ExtFreqSF=F
F=External frequency (Quartz pressure sensor) scale factor.
VOffset0=,
VSlope0=,
. . .
VSlope5=,
VOffset5=
Voltage channel offsets and slopes are all factory set, and
should never be modified by customer. These are properties of
19plus V2 electronics, and are not calibration coefficients for
auxiliary sensors. Enter calibration coefficients for auxiliary
sensors in .xmlcon or .con file in Seasave and/or SBE Data
Processing.
Hardware
Configuration
Factory Settings – do not modify in the field
SetMfgDate=
SetPcbSerialNum1=, SetPcbSerialNum2=,
SetPcbSerialNum3=, SetPcbSerialNum4=
SetPcbAssembly1=, SetPcbAssembly2=,
SetPcbAssembly3=, SetPcbAssembly4=
Auxiliary Sensor Settings – can be modified in
the field to accommodate changes in
auxiliary sensors cabled to 19plus V2
SetVoltType0=, SetVoltSN0=
SetVoltType1=, SetVoltSN1=
SetVoltType2=, SetVoltSN2=
SetVoltType3=, SetVoltSN3=
SetVoltType4=, SetVoltSN4=
SetVoltType5=, SetVoltSN5=
SetSerialType=, SetSerialSN=
- SBE 19plus V2 1
- SEACAT Profiler 1
- Limited Liability Statement 2
- Table of Contents 3
- Section 1: Introduction 5
- Unpacking SBE 19plus V2 6
- System Description 7
- Specifications 11
- Continued from previous page 12
- Sample Timing (Moored Mode) 14
- Batteries 15
- Battery Endurance 15
- External Power 17
- Data Storage 19
- Data I/O 19
- Magnetic Reed Switch 19
- Vertical Mount 20
- Horizontal Mount 23
- Section 3: 24
- See SeatermV2’s Help files 25
- See Seaterm232’s Help files 25
- Profiling Mode 31
- Moored Mode 32
- Pump Operation - General 33
- Pump Operation - Moored Mode 34
- Real-Time Setup 36
- Timeout Description 37
- Command Descriptions 38
- Status Commands (continued) 40
- Profiling Mode (MP) 58
- Moored Mode (MM) 58
- Data Output Formats 66
- Setup for Deployment 78
- Deployment 79
- Acquiring Real-Time Data 82
- Recovery 84
- Uploading Data 85
- The commands and responses 87
- Command/Data Echo Area 87
- Editing Raw Data File 91
- Corrosion Precautions 92
- Plumbing Maintenance 93
- Replacing Alkaline Batteries 94
- CAUTION: 97
- Do not recharge the Ni-Cad 97
- Barbed caps for cleaning 98
- Pressure Sensor Maintenance 99
- Pump Maintenance 99
- 8-inch socket wrench; 100
- Sensor Calibration 101
- Pressure Sensor 102
- Section 6: Troubleshooting 103
- Problem 4: Program Corrupted 104
- Glossary 105
- Sensor Interface 107
- Real-Time Clock 107
- Sensors 107
- Battery Wiring 108
- Appendix II: 109
- DESCRIPTION 110
- WetLabs=x 110
- AF24173 ANTI-FOULANT DEVICE 114
- AF24173 Anti-Foulant Device 115
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales